Car Model Magazine

Podiums with his own hands VAZ 2110

In order to make their own podiums for vases 2110, you will need these materials: - plywood 10 millimeter, about 1 square meter of plywood and another 3-millimeter, about 0.7 square meters - a cardboard to make layouts - polyurethane foam, approximately 500 grams - 0.25 millimeter fiberglass, approximately 1 square meter - 1.5 liters of epoxy resin - 0.1 liters Hardener - 1 liter solvent - 0,5 kg filler with fiberglass - Spatula Rubber - screws 15 mm and 20 mm, 15 pieces with large round head - 14 pieces of wood screws, flat head - the nails of 10 mm, about a matchbox - 1 square meter of artificial leather, the color of the shell door. In addition, you will need tools such as shliferka, jigsaw, electric drill and various screwdrivers and knives. The process of manufacturing the catwalks are not very original. From the beginning to make a power cage. Take a 10-mm plywood for the base, which is adjacent to the casing of the door, as well as an oval, which will be attached speaker. To fit the base. Relief under the skin, it is necessary to adjust the base for this, we use 3-mm pieces of plywood. On the ground, fix oval, with 3 uprights which secures with screws countersunk head. The fourth stand you do not need the base serves instead. Next on the basis of applied polyurethane foam, maintains her day around. After, cut the foam residue, a knife and process coarse sandpaper. This must be done in order to give the correct form of a skeleton. Then, it is necessary to prepare the surface for laminating fiberglass. All errors must be carefully paint over putty, it should be applied thinly. Next wait until it dries and process shliferkoy in order to get rid of the irregularities. Next take the fiberglass. Before you start, it must be burned with a blowtorch, or at the stake, so that no more wax. The thickness of the glass is not very important, thin 0.25 mm or less falls better. But still she repeats all the irregularities. That she was tough, you need to apply multiple layers. Make a mixture of epoxy resin and hardener, the ratio should be approximately 20 to 1. Until the desired consistency to the mix we must add the solvent, and then stir well to avoid lumps remain. Next, soak the fiberglass, and then apply a thin layer of cooked weight to the podium. Lay fiberglass, gently smoothing it so as not to remain the folds and bubbles. Excess material is cut with scissors. Dry it should be at least one day. When everything is dry, you need to carefully cut the hole for the speaker, it should be done with a knife with serrated edges. If you have any inaccuracies, delete them shliferkoy. Then try on as catwalk falls on the door trim. Next, you must drag the catwalks of artificial skin. To begin to tighten the skin so that never appeared folds. All secure with nails and skin, which is located on the oval speaker, glue super glue to it from slipping when you'll cut it. Internal illumination of speakers to do so: Take the hot melt glue and spread them all the surface dynamics of the reverse side. Attach a chuck 8 bulbs, which were previously in the old device, connect them in parallel. And then bring out their individual connector. In the next stage of work, you need to cut an oval under the speaker in the casing of the door. Then the inside of the base runway, apply a small layer of sealant, and then simultaneously with the speaker tighten all screws to the casing of the door. Now, work with sound insulation. Take the 3-millimeter plywood and carefully cut out the elements that echo the holes in the doors. On the inner side of the sheathing, place foam sheet, about 8 millimeters, secure it by regular clip-herringbone. Finally, you need to stretch for new speaker wire. One wire to open the door handle and the second to illuminate the dynamics. After all the jacks connect and replace the lining, then close the openings with decorative accents from the old speakers. Laths can be bought bundled together with an artificial skin.